| Item |
Characteristics |
| Operating Temperature Range |
-40 to +85°C |
| Rated Voltage Range |
4 to 50VDC |
| Capacitance Range |
0.1 to 150µF |
| Capacitance Tolerance |
±20% (M) at +20°C, 120Hz |
| Leakage Current |
I = 0.01CV or 3µA, whichever is greater, after 2 minutes at +20°C.
Where I = Leakage current (µA), C = Nominal capacitance (µF) and V =
Rated voltage (V) |
Dissipation Factor
(Tan d) |
At +20°C, 120Hz
| Rated Voltage (V) |
4 |
6.3 |
10 |
16 |
25 |
35 |
50 |
| Size A6 |
0.76 |
0.42 |
0.32 |
0.26 |
0.20 |
0.18 |
0.16 |
| Size B6 |
0.74 |
0.40 |
0.30 |
0.24 |
0.18 |
0.16 |
0.14 |
| Size B8 |
0.64 |
|
|
|
0.16 |
0.14 |
0.12 |
| Size C6 |
0.64 |
0.40 |
0.30 |
0.24 |
0.18 |
0.16 |
0.14 |
| Size C8 |
0.52 |
0.36 |
0.28 |
0.24 |
0.16 |
0.14 |
0.12 |
| Size D6-D13 |
0.52 |
0.36 |
0.28 |
0.24 |
0.16 |
0.14 |
0.12 | |
| Low Temperature Characteristics |
At 120Hz, impedance (Z) ratio between the -25°C or -40°C value and
+20°C value shall not exceed the values given below.
| Rated Voltage (V) |
4 |
6.3 |
10 |
16 |
25 |
35 |
50 |
| Z(-25°C)/Z(+20°C) |
Size A6 |
10 |
7 |
5 |
4 |
3 |
2 |
2 |
| Size B6 |
9 |
6 |
4 |
3 |
2 |
2 |
2 |
| Size B8 |
9 |
|
|
|
2 |
2 |
2 |
| Size C6 |
9 |
6 |
4 |
3 |
2 |
2 |
2 |
| Size C8 |
7 |
4 |
3 |
2 |
2 |
2 |
2 |
| Size D6-D13 |
7 |
4 |
3 |
2 |
2 |
2 |
2 |
| Z(-40°C)/Z(+20°C) |
Size A6 |
18 |
13 |
10 |
8 |
6 |
5 |
5 |
| Size B6 |
17 |
12 |
9 |
7 |
5 |
4 |
4 |
| Size B8 |
17 |
|
|
|
4 |
3 |
3 |
| Size C6 |
17 |
12 |
9 |
7 |
5 |
4 |
4 |
| Size C8 |
15 |
10 |
8 |
6 |
4 |
3 |
3 |
| Size D6-D13 |
15 |
10 |
8 |
6 |
4 |
3 |
3 | |
| Load Life |
The following specifications shall be satisfied when the capacitors
are restored to +20°C after subjecting them to the DC rated voltage for
2,000 hours at +85°C. The sum of DC voltage and peak AC voltage must not
exceed the full rated voltage of the capacitors.
Capacitance change:
Size A6: <= ±30% of the initial measured value
Size
B6, B8, C6: <= ±25% of the initial measured value
Size C8, D6-D13:
<= ±20% of the initial measured value Tan d (DF): <=
200% of the initial specified value
Leakage current: <= initial
specified value |
| Shelf Life |
The following specifications shall be satisfied when the capacitors
are restored to +20°C after exposing them for 500 hours at +85°C without
voltage applied. The rated voltage shall be applied to the capacitors for
a minimum of 30 minutes, at least 24 hours and not more than 48 hours
before the measurements.
Capacitance change: <= ±15% of the initial measured value
Tan d
(DF): <= 150% of the initial specified value
Leakage current: <=
initial specified value |
| Other |
Satisfies characteristic W of JIS C5141 |
